STATIRON DZ4
Model	DZ4
Signal detection method	Oscillating chopper *1
Frequency of data indication	Each 0.5 second
Measurement range	Normal mode: 0.01~19.99 kV I.B mode: 0.001~1.999 kV
Measurement distance	30 mm (between measurement object and sensor)
Measurement distance adjust	Red Light focusing system
Angle of the rotary sensor head	180 degree (hold each 45 degree)
Indicator	LED indicator with back light
Polarity display	Both positive and negative polarity
Mode select	With MODE select button
Battery check	Indicate in LED indicator
Power supply	DC 9V alkaline battery 006P
Operating Environment	0 to 40℃
Main unit dimensions	66×22×138 mm (W×H×D)
Wight	130 g
Accessories	9V battery, soft storage case
*1: The oscillating chopper is very susceptible to shock such as being dropped. Take care not to subject when using it.

STATIRON DX
Model	DX-01	DX-02
Signal detection method	Oscillating chopper *1
Surface potential measurement
Potential measurement range	Lo mode: 0 to ±1999V; Hi mode: 0 to 19.99kV
Measurement accuracy	±10% of rdg ±2 digits Lo mode: 1V resolution; Hi mode: 10V resolution
Measurement distance	Lo mode: 30mm; Hi mode: 50mm( between measurement object and sensor)/span>
Measurement distance adjust	Red LED light focusing system adjustment (the light mark focusing distance is 30mm or 50mm)
Measurement object correction	Standard 200×200mm / 50×50mm
Polarity display	Negative polarity( - ) only
Battery check	Amount of power remaining indicated on the display
Attenuation measurement *2
Potential attenuation ranges	-	±1000V to ±100V/±100V to ±10V
Timer display	-	0.0s to 900.0s
Potential display	-	0V to ±2000V
Ion balance measurement *3
Alarm potential	-	Outside the -100 to + 100V / -10 to + 10V ranges
Potential display	-	0 to ±200V
Other functions
Functions	Memory function for measured data Automatic power Off( after 15 minutes of non-activity) Automatic zero adjustment, analog output	Memory function for measured data PC connection data managemen(t real time/memory mode) *3 *4 Automatic power Off( after 15 minutes of non-activity) Automatic zero adjustment, analog output
Power supply	One 9 VDC alkaline battery for approximately 15 hours of continuous operation
Operating Environment	0 to 40℃
Main unit dimensions	66×25×150mm(W×H×D)
Weight	200g(including battery)
Accessories	AC adapter, 9VDC alkaline battery, grounding wire,cable for analog recorder, soft case for main unit	AC adapter, 9VDC alkaline battery, grounding wire,cable for analog recorder, soft case for main unit, Charged plate A, charged plate B, cable for charged plate B,PC connection cable(RS-232C), PC connection software(DX-TOOL), stand, hard storage case for storing the options together with the main unit.
*1: The oscillating chopper is very susceptible to shock such as being dropped. Take care not to subject when using it.
*2: The optional charged plate A or plate B( and the cable for plate B) are required to enable this function to be used.
*3: The optional PC connection cable and PC connection software are required for connection to a PC.
*4: Microsoft® Excel® software( 2000, 2002 or 2003) is required to enable use of the PC connection software( DX TOOL). This software operates in the Windows 98, Windows 2000 and Windows XP environments.Case of WINDOWS VISTA, please use indication for a classic mode.

STATIRON DS3H
Model	DS3H
Model name	TYPE-A: DS3H-A / TYPE-B: DS3H-B
Signal detection method	Oscillating chopper *1
Potential measurement range	TYPE-A: 0.000 to ±1.999kV (overscale display: 1 or -1) TYPE-B: 0.00 to ±19.99kV (overscale display: 1 or -1)
Measurement accuracy	±5% of rdg ±2 digits (TYPE-A: 1V resolution, TYPE-B: 10V resolution)
Measurement distance	TYPE-A:5 mm, TYPE-B: 30 mm (between measurement object and sensor)
Polarity display	Negative polarity (-) only
Power supply	12 VDC mode: 12 VDC adapter 1A, AC100 to 240V
Contact output terminals	COM-NC, COM-NO; contact ratings: 125 VAC 0.3A, 30 VDC 1A
Contact output	TYPE-A: 1V at 1kV, output impedance: 100 Ω TYPE-B: 1V at 10kV, output impedance: 100 Ω
Alarm output setting range	TYPE-A: ±0.200 to 1.999kV, accuracy ±10% (settable in 1-V units) TYPE-B: ±2.00 to 19.99kV, accuracy ±10% (settable in 10-V units)
Alarm output	WARNING (red LED) lights Buzzer (with ON/OFF switch) output for approx. 1s
Operating Environment	0 to 40℃
Dimensions	Main unit: 202×182×61 mm; Head section:12×93×18 mm(W×H×D)
Wight	Main unit: 1.7kg; head unit:135g
Accessories	AC adapter (100 to 240 VAC), dedicated hard case
*1: The oscillating chopper is very susceptible to shock such as being dropped. Take care not to subject it to strong shock when using it.

STATIRON DP
Model	DP
Signal detection method	Oscillating chopper *1
Plate Size	70×32 mm (IEC standard 150×150 mm)
Plate Capacity	12pF ±1pF
Measuring Accuracy	±10%rdg ± 2 digit
Measuring Voltage Range	0~±1999 V
Measuring Time range	0.0 to 99.9 sec
Angle of Rotary head	180 degree (hold each 45 degree)
Battery Check	Indicate in LCD indicator
Power Supply	Two 1.5V DC AA-type alkaline battery or AC adapter
Weight	240 g
Main Unit Dimensions	71×174×31 mm (W×H×D)
Accessories	1.5V DC AA-type battery (2 pcs), Soft case, Grounding cable
Operation Environment	0~40℃ *2
Optional Part	AC Adapter(ODP-DA) for AC100 to 240V
*1: The occilation chopper is very susceptible to shock such as being dropped. Take care not to subject it to strong shock when using it.
*2: Under high humidity environment as over 85% humidity, it will cause the problem to charge the high voltage onto the plate

SHOETESTERⅡ
Model	SHOETESTERⅡ
Measurment voltage	10VDC
Measurment accuracy	±10%+2digit
Measuring Range	0.00 to 200.0MΩ
Display	4 digit red LED display, automatic decimal point setting
Upper limit value	1,5,10,20,35,50,100MΩ
Lower limit value	0.1,0.5,1,5,10MΩ
Alarm	If the measured value is within range: OK light (green) If the measured value exceeds the maximum value: HI light (red) If the measured value exceeds the minimum value: LOW light (red)
Buzzer ON/OFF mode	1:measurement results 2:measurement complete
Function check	Ohm self-check button, 0.95 to 1.05MΩ (Display green)
Power supply	DC12V AC Adapter(100 to 240VAC)
Operating Environment	0 to 40℃
Dimensions	Main unit: 170×140×37mm(W×D×H) Measurement stand: 320×320×23mm(W×D×H)
Weight	Main unit: 0.9kg Measurement stand: 4.5kg
Option	Support pole with amgle adjustment function: OPSHT2-PA OK/NG signal cable: OPSHT2-SCA RS-232C cable: OPSHT2-RCA

MEGARESTAⅡ
Model	MEGARESTAⅡ-R (with SSD-R type probe) MEGARESTAⅡ-A (with SSD-A type probe MEGARESTAⅡ-RA (with SSD-R and A type probes)
Measuring Range	1×104 to 1012Ω 9 range automatically switching Indication as" Over range" /" Under range"
Data Indication	Graphic LCD 128×64 dot with Back Lighted Number indication: Each range 1.0 to 9.9 Range Indication:×104 to 1012Ω
Impressed Voltage	10 / 100 / 500V
Timer function	OFF / 10 / 60 sec and Hold function
Power	DC 9V mode( AC adapter AC100 to 240V) Battery Mode( DC6V Alkaline Battery AA: 4 pcs)
Working time	Approx. 6 hours( with Alkaline Battery use)
Available environment	Temperature: 0 to 40℃ Humidity: under 80%RH( without condensation)
Other functions	1:Memorize measured data (Max 100 points) 2:Data output to PC thru RS232C 3:Measurement signal output (0-2.5VDC)
Probe	Choice probe with SSD-A(OMGR-A) / SSD-R(OMGR-R) / two probes when you purchase
Weight	under 1100g( with battery)
Dimensions	162×160×60 mm( W×D×H)
Accessaries	Main body, Probe, AC adapter, AA battery( 4pcs), Soft carrying case

STATIC HONESTMETER
Model	H0110
Input voltage	100VAC ±10%(50/60Hz)
Capacity	100VA
High-voltage power supply output	H.V(applied voltage for corona discharge): 0 to 10kV
	CAL(applied voltage for calibration): 0 to 3kV
Operating Environment	temperature : 0 to 40℃
	humidity : 20 to 90% RH(non-condensing)
Output signals	ANALYZER terminal: for the analyzer SYNC terminal: for the oscilloscope Voltage: 0 to ±10V Accuracy: Approx. 10%
Main unit dimensions	420×450×280mm(W×H×D)
Weight	Approx. 33kg
Accessories	Power supply cord, signal cable calibration jig and balancer(one set) hexagonal wrenches(2), 2A fuse(3)

HONEST DATA ANALYZING SYSTEM
Model	V2
Input voltage	100VAC ±10%(50/60Hz)
Capacity	0.5VA
Main unit dimensions	300×250×100mm(W×H×D)
Weight	Approx. 1kg
Operating environment	Supported model
	DOS/V computer with a USB interface Intel Pentium 500 MHz or faster (or equivalent) At least 128 MB of memory recommended, depending on the capacity required by the OS • Hard disk drive (HDD): At least 2 GB of available space • Screen resolution: 1024 × 768 or greater recommended
	Operating systems (OS)
	Windows Vista (32 bit), Windows XP (SP2 or later, 32 bit) Windows 7(32 bit) (Please change Windows to Classic view)
Accessories	Power supply cord, connection cable USB cable, Temperature/humidity sensor, CD-ROM(Manual and drivers), Stand

CHARGED PLATE MONITOR
Model	H0601
Signal detection method	Oscillating chopper *1
Plate size	150×150mm
Electric capacitance	20pF ±2pF
Voltage measurement accuracy	±5% of rdg
Display voltage	0 to ±1999V; accuracy ±2V
Display timer	0.0 to 1999.9s; accuracy ±50ppm
Decay time measurement	+	Initial charged voltage : +1000V or more
		FIX mode	Measurement start voltage : +1000V
			Measurement end voltage : +100V
		FREE mode	Measurement start voltage : 0 to +1000V
			Measurement end voltage : 0 to +1000V
	-	Initial charged voltage : -1000V or more
		FIX mode	Measurement start voltage : -1000V
			Measurement end voltage : -100V
		FREE mode	Measurement start voltage : 0 to -1000V
			Measurement end voltage : 0 to -1000V
Offset potential measurement(measurement of ion balance characteristics)	UNBALANCE ONCE		Display hold function for one voltage and time sensing operation
	UNBALANCE SUM		Display of continuous sensing and elapsed time
	Upper limit voltage setting		0 to ±1000V(knob used to make the setting)
	Lower limit voltage setting:		0 to ±1000V(knob used to make the setting)
Auxiliary functions	Resetting of plate voltage(zero adjustment function)
	Holding of voltage and time displays during measurement
	Voltage peak hold and alarm buzzer(when voltage unbalance occurs)
Power supply	AC adapter, 12V 120mA, four AA-type alkaline batteries
External output	Measurement voltage(normal operation) alarm(contact output)
Operating Environment	0 to 40℃
Main unit dimensions	265×200×200mm(W×H×D)
Weight	Approx. 2.4kg
Accessories	AC adapter(100 to 240VAC), dedicated hard case, AA-type batteries(four)